一、创建项目

1. 创建新产品
2. 进入项目可查看信息

二、添加数据点

根据系统的需求添加数据点，可参考本系统数据点

三、进行虚拟设备调试

1. 创建好数据点后，进行虚拟设备调试
2. 在机智云APP能够观察机智云平台模拟的数据
   根据系统的需要添加或修改数据点信息

四、下载MCU代码包

在确定数据点无误后，点击MCU开发
生成代码包后，把代码包导入Arduino IDE开发环境的libraries文件中，libraries是Arduino的库文件，包含自带的库文件和用户添加的外部库文件
把networkConfig.ino的配网代码移植到simpleTry.ino,把串口打印的代码注释起来，可参考[资料分享] 史上最详细的Arduino uno R3接入机智云教程
然后根据要求修改代码，以下仅供参考：

#include <Gizwits.h>
#include <Wire.h>
#include <SoftwareSerial.h>
#include <dht.h>
int con_ledPin = 13;    //成功连接网络，13引脚低电平
int smokePin = 2;
int movePin = 3;
int alarmPin = 4;
int ledPin = 5;
int relayPin1 = 8;
int relayPin2 = 9;
int firePin = A0;
int lightPin = A1;
int beepPin = 10;
int temhumPin = 11;
bool alarmflag = 0;
dht myDHT_11;
SoftwareSerial mySerial(A2, A3); // A2 -> RX, A3 -> TXGizwits myGizwits;
#define   KEY1              6
#define   KEY2              7
#define   KEY1_SHORT_PRESS  1
#define   KEY1_LONG_PRESS   2
#define   KEY2_SHORT_PRESS  4
#define   KEY2_LONG_PRESS   8
#define   NO_KEY            0
#define   KEY_LONG_TIMER    3
#define   ALARM_SHORT_PRESS 16
#define   ALARM_LONG_PRESS  32
unsigned long Last_KeyTime = 0;unsigned long gokit_time_s(void)
{return millis() / 1000;
}
char gokit_key1down(void)
{unsigned long keep_time = 0;if (digitalRead(KEY1) == LOW){delay(100);if (digitalRead(KEY1) == LOW){keep_time = gokit_time_s();while (digitalRead(KEY1) == LOW){if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER){Last_KeyTime = gokit_time_s();return KEY1_LONG_PRESS;}} //until open the keyif ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER){return KEY1_SHORT_PRESS;}return 0;}return 0;}return 0;
}
char gokit_key2down(void)
{unsigned long keep_time = 0;if (digitalRead(KEY2) == LOW){delay(100);if (digitalRead(KEY2) == LOW){delay(100);if (digitalRead(KEY2) == LOW){keep_time = gokit_time_s();while (digitalRead(KEY2) == LOW) //until open the key{if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER){Last_KeyTime = gokit_time_s();return KEY2_LONG_PRESS;}}if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER){return KEY2_SHORT_PRESS;}return 0;}return 0;}return 0;
}
//室内报警监测
char gokit_alarmdown(void)
{unsigned long keep_time = 0;if (digitalRead(alarmPin) == LOW){delay(100);if (digitalRead(alarmPin) == LOW){keep_time = gokit_time_s();while (digitalRead(alarmPin) == LOW) //until open the key{if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER){Last_KeyTime = gokit_time_s();return ALARM_LONG_PRESS;}}if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER){return ALARM_SHORT_PRESS;}return 0;}return 0;}return 0;
}
char gokit_keydown(void)
{char ret = 0;ret |= gokit_alarmdown();ret |= gokit_key2down();ret |= gokit_key1down();return ret;
}
void KEY_Handle(void)
{/*  Press for over than 3 second is Long Press  */switch (gokit_keydown()){case KEY1_SHORT_PRESS:myGizwits.setBindMode(WIFI_PRODUCTION_TEST);break;case KEY1_LONG_PRESS:myGizwits.setBindMode(WIFI_RESET_MODE);break;case KEY2_SHORT_PRESS:myGizwits.setBindMode(WIFI_SOFTAP_MODE);//Soft AP modebreak;case KEY2_LONG_PRESS:myGizwits.setBindMode(WIFI_AIRLINK_MODE);//AirLink modebreak;case ALARM_SHORT_PRESS:alarmflag = ((alarmflag == 0) ? 1 : 0);if (alarmflag){digitalWrite(beepPin, LOW);}else{digitalWrite(beepPin, HIGH);}break;case ALARM_LONG_PRESS:digitalWrite(ledPin, HIGH); //设置为高电平digitalWrite(relayPin1, HIGH); //设置为高电平digitalWrite(relayPin2, HIGH); //设置为高电平break;default:break;}
}
//获取温度数据int dht_11_gettemperature() {int chk = myDHT_11.read11(temhumPin);int value = myDHT_11.temperature;return value;
}
//获取湿度数据int dht_11_gethumidity() {int chk = myDHT_11.read11(temhumPin);int value = myDHT_11.humidity;return value;
}
/**Serial Init , Gizwits Init@param none@return none
*/
void setup() {// put your setup code here, to run once:mySerial.begin(115200);pinMode(KEY1, INPUT_PULLUP);pinMode(KEY2, INPUT_PULLUP);pinMode(smokePin, INPUT);  //设置为数字输入模式pinMode(movePin, INPUT);pinMode(alarmPin, INPUT_PULLUP);pinMode(firePin, INPUT);pinMode(lightPin, INPUT); //模拟量为输入模式pinMode(beepPin, OUTPUT); //设置为数字输出模式pinMode(ledPin, OUTPUT);pinMode(relayPin1, OUTPUT);pinMode(relayPin2, OUTPUT);pinMode(con_ledPin, OUTPUT);digitalWrite(beepPin, HIGH); //设置为高电平myGizwits.begin();
}
void wifiStatusHandle()
{if (myGizwits.wifiHasBeenSet(WIFI_CON_ROUTER)){digitalWrite(con_ledPin, HIGH); //设置为低电平digitalWrite(ledPin, HIGH); //设置为高电平digitalWrite(relayPin1, HIGH); //设置为高电平digitalWrite(relayPin2, HIGH); //设置为高电平}
}
/**Arduino loop@param none@return none
*/
void loop() {//Configure network//if(XXX) //Trigger Condition//myGizwits.setBindMode(0x02);  //0x01:Enter AP Mode;0x02:Enter Airlink Modebool varW_Alarm = alarmflag;//Add Sensor Data CollectionmyGizwits.write(VALUE_Alarm, varW_Alarm);unsigned long varW_fire = analogRead(firePin);//Add Sensor Data CollectionmyGizwits.write(VALUE_fire, varW_fire);unsigned long varW_Move_Test = digitalRead(movePin);//Add Sensor Data CollectionmyGizwits.write(VALUE_Move_Test, varW_Move_Test);unsigned long varW_Tem = dht_11_gettemperature();//Add Sensor Data CollectionmyGizwits.write(VALUE_Tem, varW_Tem);unsigned long varW_Hum = dht_11_gethumidity();//Add Sensor Data CollectionmyGizwits.write(VALUE_Hum, varW_Hum);unsigned long varW_Light = analogRead(lightPin);//Add Sensor Data CollectionmyGizwits.write(VALUE_Light, varW_Light);bool varR_LED_OnOff = 0;if (myGizwits.hasBeenSet(EVENT_LED_OnOff)){myGizwits.read(EVENT_LED_OnOff, &varR_LED_OnOff); //Address for storing dataif (varR_LED_OnOff == 0){digitalWrite(ledPin, HIGH);}else{digitalWrite(ledPin, LOW);}}bool varR_Relay_1 = 0;if (myGizwits.hasBeenSet(EVENT_Relay_1)){myGizwits.read(EVENT_Relay_1, &varR_Relay_1); //Address for storing dataif (varR_Relay_1 == 0){digitalWrite(relayPin1, HIGH);}else{digitalWrite(relayPin1, LOW);}}bool varR_Relay_2 = 0;if (myGizwits.hasBeenSet(EVENT_Relay_2)){myGizwits.read(EVENT_Relay_2, &varR_Relay_2); //Address for storing dataif (varR_Relay_2 == 0){digitalWrite(relayPin2, HIGH);}else{digitalWrite(relayPin2, LOW);}}bool varR_beep = 0;if (myGizwits.hasBeenSet(EVENT_beep)){myGizwits.read(EVENT_beep, &varR_beep); //Address for storing dataif (varR_beep == 0 ){digitalWrite(beepPin, HIGH);}else{digitalWrite(beepPin, LOW);}}KEY_Handle();wifiStatusHandle();myGizwits.process();
}

五、下载Android开发代码包

1.在应用开发生成APP代码包
通过Android Studio软件导入项目进行编译，因版本问题需要修改关键词，compile 均替换为implementation，testcompile均替换为testimplementation，可参考以下代码：

apply plugin: 'com.android.application'android {compileSdkVersion 25buildToolsVersion '28.0.2'useLibrary 'org.apache.http.legacy'defaultConfig {applicationId "com.gizwits.opensource.appkit"minSdkVersion 16targetSdkVersion 25versionCode 1versionName "2.5.1.072715"multiDexEnabled true}buildTypes {release {minifyEnabled falseproguardFiles getDefaultProguardFile('proguard-android.txt'), 'proguard-rules.pro'}}
}dependencies {implementation fileTree(dir: 'libs', include: ['*.jar'])implementation 'com.android.support.constraint:constraint-layout:1.1.0'testImplementation 'junit:junit:4.12'implementation 'com.android.support:appcompat-v7:24.2.1'implementation files('libs/BLEasyConfig.jar')implementation files('libs/easylink2.0.jar')implementation files('libs/GizWifiSDK.jar')implementation files('libs/jpush-android-2.1.5.jar')implementation files('libs/Lark7618SDK_noudp1606031910_0101.jar')implementation files('libs/libammsdk.jar')implementation files('libs/libForEElink.jar')implementation files('libs/LSFSK_1.0.jar')implementation files('libs/ltlink2.jar')implementation files('libs/mta-sdk-1.6.2.jar')implementation files('libs/OneShotConfig.jar')implementation files('libs/open_sdk_r5756.jar')implementation files('libs/pushservice-5.6.0.30.jar')implementation files('libs/simpleconfigwizardlib.jar')implementation files('libs/xUtils-2.6.14.jar')implementation files('libs/zxing.jar')implementation 'com.android.support:design:25.3.0'implementation 'com.yanzhenjie:permission:1.0.5'
}

同时可参考基于机智云AIoT平台的Android开源app修改教程

使项目成功编译